1968 Triumph TR250 restoration

Post Reply
mooreken
Posts: 628
Joined: Sat May 09, 2015 12:25 pm

1968 Triumph TR250 restoration

Post by mooreken »

My brother and I have gotten a new project car to restore just for fun (and hopefully a little more $$$ than we will have in it). As the Subject header noted it is a '68 Triumph. My brother is making videos of the progress for his Triumph Club up in Ohio and I will put links here as I get them.

They are in HD but you might have to click on the "gear" in the lower left corner of the YouTube video if you are not watching it full screen.

The car is one of the last 100 built and has very nice outside sheet metal hardly any dents and no rust on the bolt on parts. I even think most of the tires are the original Red Line Michelins. The car sat outside with a bad convertible top for a LONG time so the floor pans and inner rocker panels are gone. But I have new panels and this is what I do. ..]
The engine area is very honest as they say. It has original heater and radiator hoses and all the clips and hardware is also as it came from the factory.
It is in a storage area 'til June to process paperwork so no updates for a while.
Enjoy and comment if you wish.

https://youtu.be/TmSifPojAdc
https://youtu.be/3t6Uq8fIOs0
mooreken
Posts: 628
Joined: Sat May 09, 2015 12:25 pm

Re: 1968 Triumph TR250 restoration

Post by mooreken »

We have started to work on the Tr250. My brother is making short videos of our progress as we go along. I'll repost the from time to time.

https://www.youtube.com/watch?v=ZzkAkJbt9mI

https://www.youtube.com/watch?v=Y62QyYstYXg
Tom Wells
Posts: 977
Joined: Fri May 08, 2015 7:34 pm
Contact:

Re: 1968 Triumph TR250 restoration

Post by Tom Wells »

Ken,

A very interesting project! Keep the reports coming, please. We can all learn something from this.

Tom
mooreken
Posts: 628
Joined: Sat May 09, 2015 12:25 pm

Re: 1968 Triumph TR250 restoration

Post by mooreken »

mooreken
Posts: 628
Joined: Sat May 09, 2015 12:25 pm

Re: 1968 Triumph TR250 restoration

Post by mooreken »

mooreken
Posts: 628
Joined: Sat May 09, 2015 12:25 pm

Re: 1968 Triumph TR250 restoration

Post by mooreken »

Removing the bolt on parts of the frame.

https://www.youtube.com/watch?v=KJE9RD_OXkw

We tried to start the motor but didn't get any farther than the carbs. One if them has a vent hole for the float bowl plugged somewhere and the fuel is running out everywhere.....We will keep pluggin' away at it.
mooreken
Posts: 628
Joined: Sat May 09, 2015 12:25 pm

Re: 1968 Triumph TR250 restoration

Post by mooreken »

We tried to start the motor today. It almost make it but my can of starting fluid was empty so we are holding off until I can get some.
Frame is all stripped except for the motor and trans and I am almost finished with the jig for the body.

Here are a couple more short videos.

https://www.youtube.com/watch?v=HcWQjolXM1Q

https://www.youtube.com/watch?v=bht8iI_9EDQ
mooreken
Posts: 628
Joined: Sat May 09, 2015 12:25 pm

Re: 1968 Triumph TR250 restoration

Post by mooreken »

Good day today. The old motor fired up and ran really well....idled better than my cobra. ..]
https://youtu.be/KSJS9KrvB48

Finished with building the jig for the rotisserie.
https://www.youtube.com/watch?v=YV0vYIcKxc0
mooreken
Posts: 628
Joined: Sat May 09, 2015 12:25 pm

Re: 1968 Triumph TR250 restoration

Post by mooreken »

Moving right along.
This video shows why taking the time to make the jig was worth while.

https://youtu.be/NRoTWNp4SIM
mooreken
Posts: 628
Joined: Sat May 09, 2015 12:25 pm

Re: 1968 Triumph TR250 restoration

Post by mooreken »

Disassembly is all finished...now on to part prep both motor and body.

https://www.youtube.com/watch?v=fEMwRUVMMXI
Post Reply